Docooler JINGSHA X99-8D3 Motherboard User Manual

1. Giriş və yuxarıview

The Docooler JINGSHA X99-8D3 is a high-performance ATX gaming motherboard designed for LGA2011 V3 processors. It features four-channel DDR3 memory support, an M.2 NVME slot for high-speed storage, and multiple PCI-E expansion slots, making it suitable for demanding computing tasks and gaming setups. This manual will guide you through the installation, configuration, and maintenance of your motherboard.

Şəkil 1.1: Yuxarıdan aşağıya view of the Docooler JINGSHA X99-8D3 Motherboard, showcasing its layout with CPU socket, RAM slots, and various expansion slots.

2. Əsas Xüsusiyyətlər

• M.2 NVME Support: Equipped with an M.2 hard disk port, supporting high-speed PCI-E NVME X4 for optimal operating system and application driver performance.
• Quad-Channel DDR3 Memory: Features 8 DDR3 memory slots across 4 channels, significantly improving capacity and performance, supporting up to 256GB.
• Digital Diagnostic Card: Integrated digital diagnostic card automatically tests hardware devices to ensure proper operation and assist in troubleshooting.
• Multiple PCI-E Expansion Slots: Provides 3 PCI-E expanded slots, configurable as X16/X8 to handle various workloads and multi-GPU setups.
• Davamlı tikinti: Built with a 10-layer PCB and high-quality capacitors for enhanced stability and heat resistance.

Figure 2.1: Diagram illustrating the six core technologies and features of the motherboard, including 4-channel DDR3*8, M.2 hard disk interface, digital diagnostic card, 7.1 channel audio, SATA3.0*8 interface, and Crossfire support.

3. Paketin məzmunu

Zəhmət olmasa, aşağıda sadalanan bütün əşyaların paketinizdə olduğunu yoxlayın:

• 1x Docooler JINGSHA X99-8D3 Motherboard
• 1x SATA Kabel
• 1x I/O Baffle (Backplate)
• 1x CPU Fan Board
• A bag of screws

4. Spesifikasiyalar

Şəkil 4.1: Ətraflı view of the motherboard's rear I/O panel, showing PS/2 ports, USB 2.0, USB 3.0, Gigabit Network Port, and 7.1 Audio Ports.

5. Quraşdırma və Quraşdırma

Before beginning installation, ensure your system is powered off and unplugged from the wall outlet. Handle the motherboard by its edges to avoid static discharge.

5.1 CPU -nun quraşdırılması

1. Locate the LGA2011 V3 CPU socket on the motherboard.
2. Gently push down the CPU retention lever and swing it open.
3. Align the triangular mark on your CPU with the corresponding mark on the socket. Carefully place the CPU into the socket without forcing it.
4. CPU-nu bərkitmək üçün saxlama qolunu bağlayın.
5. CPU-nun üst hissəsinə nazik, bərabər bir təbəqə termal pasta çəkin.
6. Install the CPU cooler according to its manufacturer's instructions, ensuring proper contact and pressure.

Şəkil 5.1: Yaxından view of the LGA2011 V3 CPU socket on the motherboard, ready for CPU installation.

5.2 Installing RAM Modules

1. DDR3 yaddaş yuvalarının hər iki ucundakı klipləri açın.
2. Align the notch on the RAM module with the key in the memory slot.
3. Press down firmly on both ends of the RAM module until the clips snap into place, securing the module.
4. For optimal performance, install RAM modules in matching pairs across the four channels as indicated in the motherboard manual or silkscreen.

Şəkil 5.2: View of the eight DDR3 RAM slots on the motherboard, showing their arrangement for quad-channel memory configuration.

5.3 Installing Storage Devices (M.2 NVME & SATA)

1. M.2 NVME SSD: Locate the M.2 slot. Insert the M.2 SSD at an angle into the slot, then gently push it down and secure it with the provided screw.
2. SATA Sürücüləri: Connect your SATA SSDs or HDDs to the SATA 3.0 ports using SATA data cables. Ensure the power supply SATA power connectors are also attached to the drives.

Figure 5.3: Close-up of the M.2 interface on the motherboard, highlighting its position and the PCI-E Gen3 X4 connection for high-speed data transfer.

Şəkil 5.4: View of the eight orange SATA 3.0 ports on the motherboard, providing ample connectivity for storage devices.

5.4 Enerji təchizatının qoşulması

1. Connect the 24-pin ATX power connector from your power supply unit (PSU) to the corresponding port on the motherboard.
2. Connect the 8-pin CPU power connector (EPS12V) from your PSU to the 8-pin port near the CPU socket.

5.5 Installing Expansion Cards (PCIe)

1. Locate the desired PCI-E 3.0 x16 or x1 slots.
2. Müvafiq genişləndirmə yuvasının qapağını kompüterinizin korpusundan çıxarın.
3. Align the expansion card with the slot and press down firmly until it is fully seated. Secure the card with a screw to the case.

Şəkil 5.5: Bucaqlı view of the motherboard, highlighting the three PCI Express 3.0 x16 slots and the smaller PCIe x1 slots, ready for graphics cards and other expansion cards.

6. Anakartın İşləməsi

6.1 İlk Yükləmə və BIOS Quraşdırması

1. Bütün komponentləri yığdıqdan sonra monitoru, klaviaturanı və siçanı qoşun.
2. Power on your system. During the initial boot sequence, repeatedly press the DEL or F2 key (common for JINGSHA motherboards) to enter the BIOS/UEFI setup utility.
3. In the BIOS, verify that all installed components (CPU, RAM, storage) are detected correctly.
4. Əməliyyat sistemi quraşdırma medianızı (USB sürücüsü və ya DVD) prioritetləşdirmək üçün açılış sırasını konfiqurasiya edin.
5. Dəyişiklikləri yadda saxlayın və BIOS-dan çıxın. Sistem yenidən başlayacaq.

6.2 Əməliyyat sisteminin quraşdırılması

Follow the instructions provided with your operating system (e.g., Windows, Linux) to complete the installation process. Ensure you install all necessary drivers for the motherboard's chipsets, network, audio, and other components from the manufacturer's website or included driver disc.

7. Baxım

Düzgün texniki xidmət anakartınızın uzunömürlülüyünü və sabit işləməsini təmin edir.

• Toz Təmizləmə: Ana platadan və komponentlərdən tozları sıxılmış hava ilə müntəzəm olaraq təmizləyin. Təmizləmədən əvvəl sistemin elektrikdən söndürüldüyünə və elektrik şəbəkəsindən çıxarıldığına əmin olun.
• BIOS yeniləmələri: Periodically check the Docooler or JINGSHA official website for BIOS updates. BIOS updates can improve compatibility, stability, and performance. Follow update instructions carefully to avoid damaging the motherboard.
• Sürücü Yeniləmələri: Optimal performansı və yeni proqram təminatı və avadanlıqla uyğunluğu təmin etmək üçün sistem drayverlərinizi yeniləyin.
• Ekoloji Şərtlər: Operate the motherboard in a well-ventilated environment with stable temperature and humidity to prevent overheating and component degradation.

8. Giderme

Bu bölmə qarşılaşa biləcəyiniz ümumi problemlərə toxunur.

8.1 Enerji yoxdur / Çəkmə yoxdur

• Ensure the 24-pin ATX and 8-pin CPU power connectors are securely plugged into the motherboard.
• Check if the power supply unit (PSU) is switched on and connected to a working power outlet.
• Verify that the front panel power button cable is correctly connected to the motherboard's header.

8.2 Ekran çıxışı yoxdur

• Ensure your graphics card (if dedicated) is properly seated in its PCI-E slot and has all necessary power cables connected.
• Check that your monitor cable is securely connected to the graphics card or motherboard (if integrated graphics are used, though X99 typically requires a dedicated GPU).
• Try reseating your RAM modules. Incorrectly seated RAM is a common cause of no display.

8.3 POST Code Display (Digital Diagnostic Card)

The motherboard is equipped with a digital diagnostic card (POST code display) that shows a two-digit code during boot-up. Refer to the motherboard's detailed technical documentation (often available on the manufacturer's website) for a list of POST codes and their meanings. This can help pinpoint the exact component causing a boot failure.

Şəkil 8.1: Yaxından view showing the integrated digital diagnostic card (POST code display) on the motherboard, which assists in identifying hardware issues during boot.

9. Zəmanət və Dəstək

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Docooler or JINGSHA websayt. Zəmanət iddiaları üçün satınalma sübutunuzu saxlayın.