Case Uyğun Ajax Cihazları İstifadəçi Təlimatı

 

14 mart 2025-ci il yenilənib

Case is the casing designed to install one or more compatible Ajax devices. The complete set includes the tampcihazları sabodan qorumaq üçün lövhətage. Case has fasteners to fix the cables and channels for convenient cable organization. The casing is intended for indoor use only.

Case is produced in several versions. Each model has a different number of slots depending on the device combination:

 

• Case A (106) — one Ajax device;
• Case B (175) — up to two Ajax devices;
• Case C (260) — one Ajax device and 7 Ah battery;
• Case D (430) — up to eight devices and two 18 Ah batteries.

 

Case al

Hansı Case seçmək

 

Funksional elementlər

Case A (106) Case B (175) Case C (260) Case D (430)

 

1. Holding screws to secure the casing lid. Can be unscrewed with abundled hex key (Ø 4 mm).
2. Bubble level to check the inclination angle of the mount during installation.
3. Qazma zamanı cihazı qorumaq üçün tıxaclar.
4. tampAjax cihazını birləşdirmək üçün tel ilə er board.
5. Cihazı bağlamaq üçün kilidlər.
6. Perforated part of the casing. Do not break it off. This part is necessary for tamper triggering in case of any attempt to detach thecasing from the surface.
7. Holes to attach the casing to the surface.
8. Perforated part to run the wires.
9. Fasteners to fi x the cables with ties.
10. Recesses to drill the holes conveniently.

 

Uyğun cihazlar

The number of devices installed into Case depends on the dimensions ofthe casing and its confi guration.

Uyğunluq cədvəli
Case A (106)
B işi (175)
Case C (260)
Dava D

 

Əsas xüsusiyyətlər

Case has latches for attaching devices without tools. Slide the latch toremove the device.

Cihaz iki vəziyyətdə sabitlənmişdir. 180° çevirə bilərsiniz.

 

Case has fasteners to fi x the cables with ties and channels for convenientcable routing. The casing has perforated parts to run the cables throughthe back side. There are recesses to place the drill conveniently (in caseyou need to drill holes and run the cables along the side, bottom, or top).During drilling, the tool rests on plastic stoppers, ensuring the installed devices remain protected.

A (106) və ya B qutusunun (175) qapağı quraşdırma zamanı 180° döndərilə bilər.

Case C (260) and Case D (430) have battery holders at the bottom of thecasing to prevent accidental dislodgement. The holding stripe for securingthe battery is included with Case D (430).

Case D (430) has sixteen slots for plastic holders for Fibra modulesinstallation. Holders are available in two versions:

• Module Holder (type A) for Superior LineSplit Fibra, Superior LineProtect Fibra, Superior MultiRelay Fibra attachment;
• Module Holder (type B) — for Superior Hub Hybrid (4G) (without casing) and Superior MultiTransmitter Fibra (without casing).

Dördü var Module Holder (type A) in the complete set. Additional holders and Module Holder (type B) ayrı satılır.

Superior LineSupply Fibra quraşdırma üçün sahibləri tələb etmir.

 

Quraşdırma yerinin seçilməsi

It is advisable to choose an installation site where Case is hidden fromprying eyes — for example, in the pantry. This will help reduce thelikelihood of the system sabotage. Note that the device is intended forindoor installation only.

The Case installation site must comply with the recommendations formounting the devices installed in the casing.

Follow these recommendations when designing the Ajax system projectfor an object. The system should be designed and installed byprofessionals. The list of authorized Ajax partners is burada mövcuddur

 

Korpus quraşdırıla bilməz

casing can be damaged if you install it:

1. Çöldə.
2. Inside premises with temperature and humidity values that do not correspond to the operating parameters

 

Cihazları Case-ə quraşdırmağa hazırlanır

Hansı Case seçmək

Use Case configurator to get the most optimal placement of your Fibra devices in the casing.

Kabel düzümü

When preparing to cable routing, check the electrical and fi re safety regulations in your region. Strictly follow these standards and regulations.Tips for cable arrangement are available in this article

Kabel marşrutu

We recommend you read the Selecting the installation site section carefully before installation. Avoid deviations from the system project.Violating the basic installation rules and the recommendations of this manual may lead to incorrect operation and loss of connection with devices installed into Case.

Kabeli necə çəkmək olar

Qoşulmaq üçün kabellərin hazırlanması
Remove the insulating layer and strip the cable with a special insulationstripper. The ends of the wires inserted into the device terminals must betinned or crimped with a sleeve. This ensures a reliable connection andprotects the conductor from oxidation.

Kabel necə hazırlanır

 

Quraşdırma

Before installation, ensure that you have selected the optimal location forthe casing and that it complies with the requirements of this manual.

Case A (106)
B işi (175)
Case C (260)
Case D ( 430)

Case quraşdırmaq üçün:

1. Prepare cable holes in advance: drill the holes in the bottom or side ofthe casing or break out the perforated part on the back of Case. Werecommend using a hole saw for plastic Ø16 mm or Ø20 mm.

 

Insert the pipe, corrugated pipe or conduit into the holes in the casing.

2. Route the cables and lead them through the pre-prepared holes.Secure Case on the vertical or horizontal surface at the selected installation site with the bundled screws using all fixation points. One of them is in the perforated part above the tamper — it is required fortamper triggering if someone tries to detach the casing.

3. Secure the device in the casing. Connect the cables to the corresponding terminals. Fix the cables with ties using fasteners.
4. t-ni birləşdirinamplövhəni müvafiq cihaz konnektoruna bağlayın.

 

5. Place the lid on the casing and fasten it with the bundled screws.
6. Check the state of the lid in the Ajax app. If the app shows the Front lid open state, check the tightness of Case.

 

Baxım

Cihaz texniki qulluq tələb etmir.

Texniki spesifikasiyalar

Technical specifications for Case A (106)
Technical specifications for Case B (175)
Technical specifications for Case C (260)
Technical specifications for Case D (430)
Standartlara uyğunluq

 

Zəmanət

“Ajax Systems Manufacturing” Məhdud Məsuliyyətli Cəmiyyətinin məhsullarına zəmanət alındıqdan sonra 2 il müddətində qüvvədədir.

Cihaz düzgün işləmirsə, əvvəlcə Ajax Texniki Dəstəyi ilə əlaqə saxlayın. Əksər hallarda texniki məsələlər uzaqdan həll edilə bilər.

Zəmanət öhdəlikləri
İstifadəçi Müqaviləsi

Texniki Dəstək ilə əlaqə saxlayın:

• e-poçt
• Telegram

“AS Manufacturing” MMC tərəfindən istehsal edilmişdir

 

Təhlükəsiz həyat haqqında bülletenə abunə olun. Spam yoxdur

 

Bu Təlimat haqqında ətraflı oxuyun və PDF yükləyin:

Sənədlər / Resurslar

AJAX Case Uyğun Ajax Cihazları [pdf] İstifadəçi Təlimatı Case A 106, Case B 175, Case C 260, Case D 430, Case uyğun Ajax Cihazları, Case, Uyğun Ajax Cihazları, Ajax Cihazları, Cihazlar

İstinadlar

• İstifadəçi təlimatı