Giriş
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Təhlükəsizlik Məlumatı
- Do not expose the scanner to extreme temperatures, humidity, or direct sunlight.
- Skaneri yerə salmaqdan və ya güclü zərbələrə məruz qoymaqdan çəkinin.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Keep the scanning window clean to ensure accurate barcode reading.
Paketin məzmunu
Paketinizdə aşağıdakı elementlərin olduğunu yoxlayın:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Enerji təchizatı vahidi
- Documentation (this manual or similar)
Hər hansı bir əşya itkin düşərsə və ya zədələnərsə, dərhal təchizatçı ilə əlaqə saxlayın.
Quraşdırma
1. Skaneri qoşmaq
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Skanerə qoşulun: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Enerji təchizatını birləşdirin: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. İlkin işə salın
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Skanerin işlədilməsi
1. Barkodların skan edilməsi
- Məqsəd: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- Skan: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Təsdiq: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Göstəriciləri Anlamaq
- Yaşıl LED: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Baxım
Skanerin Təmizlənməsi
- Regularly clean the scanning window with a soft, lint-free cloth dampsu və ya yumşaq, aşındırıcı olmayan təmizləyici ilə təmizləyin.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Ensure the scanner is powered off before cleaning.
Saxlama
İstifadə edilmədikdə, skaneri təmiz, quru yerdə, birbaşa günəş işığından və həddindən artıq temperaturdan uzaq saxlayın.
Problemlərin aradan qaldırılması
| Problem | Mümkün Səbəb | Həll |
|---|---|---|
| Skaner işə düşmür. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Skaner barkodları oxumur. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Spesifikasiyalar
- Model: SR30
- Hissə nömrəsi: 225-727-003 (Kit)
- Skaner növü: Xətti Şəkilçi
- İnterfeys: RS232
- İstehsalçı: İntermec
- Maddə çəkisi: 0.01 ounces (approximate, scanner only)
- Şöbə: Barkod
- ASIN: B003T0WF3S
Zəmanət və Dəstək
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec websayt. Satınalma qəbzinizi zəmanət iddiaları üçün satınalmanın sübutu kimi saxlayın.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
