1. Giriş
Thank you for choosing the PROEL DBA1CH Active Direct Box. This manual provides essential information for the safe and efficient operation of your device. The DBA1CH is designed to convert unbalanced, high-impedance instrument signals into balanced, low-impedance signals suitable for direct connection to mixing consoles or audio interfaces, minimizing noise and signal degradation over long cable runs.
2. Təhlükəsizlik Məlumatı
Please read and understand all safety instructions before operating the DBA1CH. Retain this manual for future reference.
- Güc mənbəyi: The unit can be powered by two internal 9V batteries, a 12Vdc adapter (not included), or +48V Phantom Power from a connected mixer. Ensure the correct power source is used.
- Batareyanın quraşdırılması: When installing batteries, ensure correct polarity. Remove batteries if the unit will not be used for an extended period to prevent leakage.
- Ətraf mühit: Do not expose the unit to rain, moisture, extreme temperatures, or direct sunlight. Operate in a dry, well-ventilated area.
- Xidmət: Bu cihaza özünüz xidmət göstərməyə çalışmayın. Bütün xidmətlər üçün ixtisaslı xidmət personalına müraciət edin.
- Təmizləmə: Yalnız quru parça ilə təmizləyin. Maye təmizləyicilərdən və ya aerozollardan istifadə etməyin.
3. Məhsul bitdiview
The PROEL DBA1CH is an active direct box designed for robust performance and signal integrity.
Figure 1: Front Panel Layout of the PROEL DBA1CH Active Direct Box. This image displays the various input and output jacks, including the DBA1CH Input, Link, Unbalanced Output, and Balanced Output (XLR). It also shows the PAD and GND LIFT switches, and the power indicator LED.
3.1 Ön Panel Xüsusiyyətləri
- DBA1CH Input (6.3mm Jack): Unbalanced input for connecting instruments or line-level sources.
- Link Output (6.3mm Jack): Parallel output of the input signal, typically used to feed an instrument ampömürlük.
- Unbalanced Output (6.3mm Jack): An additional unbalanced output.
- Balanslaşdırılmış Çıxış (XLR): Balanced low-impedance output for connecting to a mixer or audio interface.
- PAD keçidi: Attenuates the input signal by +20dB to prevent clipping when connecting high-output sources.
- GND LIFT Switch: Disconnects the ground connection between the input and output to eliminate hum and ground loops.
- Güc göstəricisi LED: Cihaz işə salındıqda yanır.
4. Quraşdırma
4.1 Cihazın enerji təchizatı
The DBA1CH can be powered in three ways:
- 9V batareyalar: Insert two 9V batteries into the battery compartments, ensuring correct polarity. (Batteries not included).
- 12Vdc Adapter: Connect a compatible 12Vdc power adapter (not included) to the DC input jack.
- +48V Fantom Gücü: If connected to a mixer with phantom power, the unit will automatically draw power from the XLR output.
4.2 Əsas Bağlantı
Follow these steps for a typical setup:
- Connect your instrument (e.g., guitar, bass, keyboard) to the DBA1CH Input using a 6.3mm mono jack cable.
- (İstəyə görə) qoşun Link Çıxışı to your instrument amplifier if you wish to monitor your sound on stage.
- birləşdirin Balanced Output (XLR) to a microphone input on your mixing console or audio interface using an XLR cable.
- Ensure the mixer's phantom power is enabled for the corresponding channel if you are using phantom power.
5. Əməliyyat Təlimatları
5.1 PAD Switch Usage
The PAD switch is used to attenuate the input signal by +20dB. Engage this switch if you are connecting a high-output source (e.g., active bass, keyboard, or line-level output) and notice distortion or clipping at the mixer input. For most passive instruments, leave the PAD switch in the "Normal" (off) position.
5.2 GND LIFT Switch Usage
The GND LIFT switch helps eliminate hum or buzzing noises caused by ground loops. If you hear unwanted noise in your audio signal, try engaging this switch. If the noise persists or worsens, return the switch to its original position.
6. Baxım
- Təmizləmə: Cihazın xarici hissəsini təmizləmək üçün yumşaq, quru parça istifadə edin. Aşındırıcı təmizləyicilər, həlledicilər və ya mumlardan istifadə etməyin.
- Batareyanın dəyişdirilməsi: If using battery power, replace batteries when the power indicator LED dims or the audio signal becomes weak or distorted. Always replace both 9V batteries simultaneously.
- Yaddaş: When not in use, store the unit in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the batteries.
7. Giderme
| Problem | Mümkün Səbəb | Həll |
|---|---|---|
| Səs çıxışı yoxdur. | No power; incorrect connections; faulty cables. | Check battery power or phantom power. Verify all cables are securely connected. Test with different cables. |
| Zümzümə və ya vızıldama səsi. | Ground loop; faulty cable; interference. | Cəlb edin GND LIFT switch. Try different cables. Ensure power sources are properly grounded. |
| Təhrif edilmiş səs. | Input signal too hot; faulty unit. | Cəlb edin PAD switch. Reduce the output level of the source instrument. If distortion persists, the unit may require service. |
| Power LED not illuminating. | No power; dead batteries; no phantom power. | Check battery installation and charge. Ensure phantom power is active on the mixer. Verify 12Vdc adapter connection if used. |
8. Spesifikasiyalar
- Model: PROEL DBA1CH
- Növ: Aktiv birbaşa qutu
- Girişlər: 1 x 6.3mm mono jack (unbalanced)
- Çıxışlar: 1 x 6.3mm mono jack (Link), 1 x 6.3mm mono jack (Unbalanced), 1 x XLR (Balanced)
- Nəzarətlər: PAD (+20dB attenuation), GND LIFT
- Güc Seçimləri: 2 x 9V batteries (not included), 12Vdc adapter (not included), +48V Phantom Power
- Çəki: Təxminən 250 q
- İstehsalçı: PROEL
9. Zəmanət və Dəstək
PROEL products are designed and manufactured to the highest quality standards. For warranty information and technical support, please refer to the warranty card included with your product or visit the official PROEL websayt. Satınalma qəbzinizi hər hansı zəmanət iddiaları üçün satınalmanın sübutu kimi saxlayın.
For further assistance, please contact PROEL customer service or your authorized dealer.