DuraTherm Rəqəmsal İstilik Elementi Nəzarət Cihazı Təlimat Kitabı

DuraTherm Rəqəmsal İstilik Elementi Nəzarət Cihazı Təlimat Kitabı

ELECTRICAL ELEMENT WALL CONTROLLER

Please read the instructions thoroughly before attempting to tit the product or attach it to your electrical system.

Please ensure that you chose a suitably sized electrical element for your towel warmer.

Safety Precautions: This product should Defined by a competent person who can ensure compliance with IEE. Part P and local authority regulations. Ensure the mains electrical circuit and the fused spur unit are both isolated before fining. This unit should not he fitted in IEE bathroom Zone.1.

NÖQLƏT ÇƏKİLMƏSİ TƏLİMATLARI
A fused spur is required in the supply circuit to the controller. fitted with the correct size fuse.
The 2 x E & 2 x N terminals are linked on the printed circuit board.

ELECTRICAL ELEMENT WIRES (OUT)	From Left to Right terminals 1-3 correspond to the Element cable The element wires should be connected as follows: Yaşıl/Sarı Yer to terminal 1 (N on board) Mavi Neytral to terminal 2 (L on board) Qəhvəyi Canlı to terminal 3 (L/T on board) ÇOX ƏHƏMİYYƏTLİ – Bu qurğu torpaqlanmalıdır
MAIN CABLE WIRES (IN)	From Left to Right terminals 4-6 correspond to the Mains cable wires The mains cable wires should be connected as follows: Qəhvəyi Canlı to terminal 4 (L on board) Mavi Neytral to terminal 5 (N on board) Yaşıl/Sarı Yer to terminal 6 (E on board) VERY IMPORIANT – Bu qurğu torpaqlanmalıdır
	Clamp the element cable to the bottom of the wall controller
Carefully fit the control plate into the back box ensuring that no wires are trapped during the sitting process. Use the two fixing screws to secure to the back box.

ƏMƏLİYYAT TƏLİMATLARI

There are four buttons on the control plate. ON/OFF (1), temperature Increase (2), temperaturun azalması (3), ECO boost button (4).

ƏSAS FƏALİYYƏT

The unit in standby has the main LED in QIRMIZI. To turn on in normal mode, press the ON/OFF düyməsi və
release it. The LED çevriləcək MAVİ, the Narıncı LED bank will light between one to five LED.

To increase or decrease the temperature press the ‘increase/decrease’ buttons to attain the desired setting. Each one of the ORANGE LEDs represents the following power output from the element:
5 LEDs =100% power > 4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power >1 LED = 40% power
Vahidi çevirmək üçün OFF. düyməsini basın ON/OFF düyməsini basın və buraxın.
NB The control plate contains a memory and whatever the temperature that was set when the unit was turned OFF, will be the temperature (number of LED’s lit) that the element will resume at when the unit is turned ON növbəti dəfə.

EKO FUNKSİYASI

Press the ECU button from either power on or from standard control. the power LED will turn GREEN. The
ECO function allows you to go to a higher power setting for 30 minutes (To heat the towel warmer) this power level can be set in the first 30 minutes. After 30 minutes the power is reduced to the pre-set lower level for 90 minutes. The power output can be set using the increase/ decrease buttons to set your preferred rail temperature. After 2 Hours the controller will turn on.
Both the 30 minute and the 90 minutes settings are saved in the controller.

5 LEDs = 100% power > 4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power >1 LED = 40% güc

Texniki məlumat.
Girişdən qorunma: IPX4
Cildtage: 230-245 vac
Maksimum güc çıxışı: 800w
Ölçülər: 85 x 85 x 20 mm
Təsdiqlər: CE, tested to EN55014-1:2006