M5STACK Unit C6L Intelligent Edge Computing Unit İstifadəçi Təlimatı

M5STACK Unit C6L Intelligent Edge Computing Unit İstifadəçi Təlimatı
DOMUS LINE EASI DISK Driver D Hərəkət İdarəetmə Diski İstifadəçi Təlimatı

1. KONUT

Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\

1.1. Vahid C6L

  1. Ünsiyyət Bacarıqları
    Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U
  2. Prosessor və Performans
    Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM
  3. Enerji və Enerji İdarəetmə
    Power Input: USB Type-C (5 V input) and Grove 5 V input
  4. Ekran və Göstəricilər
    0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts
  5. Interfaces & Controls
    Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control
  6. Expansion & Debug Pads
    Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug

2. SPESİFİKASİYALAR

Parametr Spesifikasiya
MCU Espressif ESP32-C6 (tək nüvəli RISC-V, 40 MHz-ə qədər)
Ünsiyyət LoRaWAN; 2.4 GHz Wi-Fi BLE
Güc Girişi USB Type-C(5V) və Grove 5V
Təchizat həcmitage 3.3 V (bortda LDO)
Flash yaddaş 16 MB SPI Flash (128 Mbit)
Ekran 0.66”SPI OLED(128×64)
Göstərici                                  WS2812C ünvanlı RGB LED
Buzzer Bortda səs siqnalı
Düymələr System button (SYS_SW)and reset button(MCU_RST)
İnterfeyslər Grove I²C;USB Type-C;bootloader pad;TP1-TP8 debug yastıqları
Antenalar 2×SSMB-JEF clamp birləşdiricilər;2×IPEX-4 antena birləşdiriciləri
İşləmə temperaturu İşləmə temperaturu
Əlavə Xüsusiyyətlər Multi-channel ESD/surge protection
İstehsalçı M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China
CE üçün tezlik diapazonu 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz
CE üçün maksimum EIRP BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm
Qəbuledici kateqoriyası The equipment provider declared that the receiver category for the EUTis2.
2.1 Modul Ölçüsü
Modul Ölçüsü

3. FCC Xəbərdarlığı

FCC Diqqəti:
Uyğunluğa cavabdeh olan tərəf tərəfindən açıq şəkildə təsdiq olunmayan hər hansı Dəyişikliklər və ya modifikasiyalar istifadəçinin avadanlığı idarə etmək səlahiyyətini ləğv edə bilər. Bu cihaz FCC Qaydalarının 15-ci hissəsinə uyğundur. Əməliyyat aşağıdakı iki şərtə tabedir: (1) Bu cihaz zərərli müdaxiləyə səbəb ola bilməz və (2) bu cihaz arzuolunmaz işə səbəb ola biləcək müdaxilə də daxil olmaqla qəbul edilən hər hansı müdaxiləni qəbul etməlidir.
Vacib QEYD:
Qeyd: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
müdaxiləni aşağıdakı tədbirlərdən biri və ya bir neçəsi ilə düzəldin:

  • Qəbul edən antenanın istiqamətini dəyişdirin və ya yerini dəyişdirin.
  • Increase the separation betweentheequipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
Arduino Quraşdırma

I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
Arduino rəsmisinə baş çəkmək üçün klikləyin websaytına daxil olun və sizin üçün quraşdırma paketini seçin
operating system to download. Ⅱ. Installing Arduino Board Management
1. İdarə Heyətinin Meneceri URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> Üstünlüklər
Arduino Quraşdırma

2.ESP board idarəçiliyini kopyalayın URL aşağıda Əlavə Şura Menecerinə daxil olun
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
Arduino Quraşdırma
Arduino Quraşdırma

3. Yan paneldə Board Manager seçin, ESP-ni axtarın və Quraşdır üzərinə klikləyin.
Arduino Quraşdırma

4. Yan paneldə Board Manager seçin, M5Stack-i axtarın və Quraşdır üzərinə klikləyin.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
Arduino Quraşdırma

5. Proqramı yükləmək üçün cihazı məlumat kabeli ilə kompüterinizə qoşun

M5STACK Logo

Sənədlər / Resurslar

M5STACK Unit C6L Intelligent Edge Computing Unit [pdf] İstifadəçi Təlimatı
M5UNITC6L, 2AN3WM5UNITC6L, Unit C6L Intelligent Edge Computing Unit, Unit C6L, Intelligent Edge Computing Unit, Edge Computing Unit, Computing Unit, Unit

İstinadlar

Şərh buraxın

E-poçt ünvanınız dərc olunmayacaq. Tələb olunan sahələr qeyd olunub *